description
Electrodes
form
suspension
composition
Propylene glycol monomethyl ether - diethylene glycol monomethyl ether solvents (PM-DGME) , Silver content, 60 wt. %
particle size distribution
100 nm (D90 by Lumisizer™), 75 nm (D50)
surface tension
, 23dyn/cm (Pendant Drop)
viscosity
26 cP (Brookfield, Cone Spindle 40, 25 °CBrookfield, Cone Spindle 40, 25 °C)
density
2.14 g/mL
storage temp.
15-25°C
Application
This product is a conductive ink based on single-crystal silver nanoparticles in a mixture of propylene glycol monomethyl ether - diethylene glycol monomethyl ether solvents (PM-DGME), has been designed for Aerosol digital printing systems and low temperature sintering applications. The ink offers a unique combination of properties, including high silver loading, low viscosity, storage at ambient conditions, long shelf life, reliable jetting and good printability. Printed patterns, sinterable at low temperatures, provide low electrical resistivity, good adhesion to a wide range of substrates and durability to humid and aqueous environments.
This product can be stored at room temperature.
Printed Electronics: FPD, RFID, PCB
Aerosol Jet can print conformal interconnects on 3D surfaces eliminating the need for wire bonding - for example printing electrical connections on 3D stacked die or for LED chip fabrication. Components can also be printed onto 3 dimensional surfaces eliminating the need for a separate substrate thereby reducing the size, thickness and weight of the end product. For example, Aerosol Jet is used to print antennas and sensors that conform to the shape of the underlying substrate such as a cell phone case. The Aerosol Jet process also supports printing on a wide variety of substrates including plastics, ceramics and metallic structures.
This product can be stored at room temperature.
- Compatible printheads
- Product fit for:
Printed Electronics: FPD, RFID, PCB
Aerosol Jet can print conformal interconnects on 3D surfaces eliminating the need for wire bonding - for example printing electrical connections on 3D stacked die or for LED chip fabrication. Components can also be printed onto 3 dimensional surfaces eliminating the need for a separate substrate thereby reducing the size, thickness and weight of the end product. For example, Aerosol Jet is used to print antennas and sensors that conform to the shape of the underlying substrate such as a cell phone case. The Aerosol Jet process also supports printing on a wide variety of substrates including plastics, ceramics and metallic structures.
Preparation Note
Mix well before use.
Electrical Properties
Sintering conditions (on glass) :
UV followed by thermal (UV 9 W/cm2, 2 min (+), Thermal: 130°C/60 min)
Resistivity after sintering conditions mentioned above : ≤10 μΩ·cm (≤6 bulk)
Adhesion to (tested) :
Kapton, PC, PC/ABS, PA, glass
Reliability :
Adhesion survived below testing conditions (on glass):
soaking in NaCl 1M for 2 h
soaking in NaCl 1M for 2 h and in DI water for 20 h
Electrical Properties
Sintering conditions (on glass) :
UV followed by thermal (UV 9 W/cm2, 2 min (+), Thermal: 130°C/60 min)
Resistivity after sintering conditions mentioned above : ≤10 μΩ·cm (≤6 bulk)
Adhesion to (tested) :
Kapton, PC, PC/ABS, PA, glass
Reliability :
Adhesion survived below testing conditions (on glass):
soaking in NaCl 1M for 2 h
soaking in NaCl 1M for 2 h and in DI water for 20 h
Legal Information
Lumisizer is a trademark of LUM GmbH
signalword
Danger
Hazard Classifications
Aquatic Acute 1 - Aquatic Chronic 1 - Carc. 2 - Eye Irrit. 2 - Flam. Liq. 3 - Met. Corr. 1 - Repr. 1B - Skin Irrit. 2
存储类别
3 - Flammable liquids
wgk
WGK 3
flash_point_f
85.1 °F
flash_point_c
29.5 °C