Merck
CN
  • Accelerated orthodontic tooth movement following le fort I osteotomy in a rodent model.

Accelerated orthodontic tooth movement following le fort I osteotomy in a rodent model.

Journal of oral and maxillofacial surgery : official journal of the American Association of Oral and Maxillofacial Surgeons (2014-03-19)
Hao Yuan, Xiaofang Zhu, Jingting Lu, Jiewen Dai, Bing Fang, Steve G F Shen
摘要

In surgery-first accelerated orthognathic surgery, the clinical phenomenon of accelerated orthodontic tooth movement after osteotomy is a benefit compared with the conventional approach. However, because much of the literature on this phenomenon is based on empirical evidence and case reports, experimental animal-based studies are needed to verify and quantify this acceleration effect. The purpose of this prospective experimental study was to identify whether osteotomy procedures increase tooth movement. Le Fort I osteotomies were performed on the left maxillas in 15 male adult Sprague-Dawley rats. After surgery, a continuous force of 0.5 N was placed on the maxillary left first molar to move the tooth mesially. Another 15 rats had no surgery and served as controls. On days 1, 14, and 28, digital caliper measurements were taken to record tooth movement. In the experimental group, the maxillary left first molars moved significantly more rapidly on days 14 and 28 (P < .05). Histologic findings showed more active alveolar bone remodeling. Le Fort I osteotomy significantly accelerated the rate of orthodontic tooth movement. Histologically, more active and extensive bone remodeling was observed after osteotomy.

材料
货号
品牌
产品描述

Sigma-Aldrich
酸性磷酸酶 来源于马铃薯, lyophilized powder, ≥0.5 unit/mg solid
Sigma-Aldrich
酸性磷酸酶 来源于小麦胚芽, ≥0.4 unit/mg solid
Sigma-Aldrich
酸性磷酸酶 来源于马铃薯, lyophilized powder, ≥3.0 units/mg solid
Sigma-Aldrich
磷酸酶(酸性) 来源于甘薯, ammonium sulfate suspension, ≥10.0 units/mg protein (modified Warburg-Christian)
Sigma-Aldrich
Raney®-镍, W.R. Grace and Co. Raney® 2400, slurry, in H2O, active catalyst
Sigma-Aldrich
镍, wire, diam. 0.25 mm, ≥99.9%
Sigma-Aldrich
镍, powder, <1 μm, 99.8% trace metals basis
Sigma-Aldrich
镍, foil, thickness 0.25 mm, 99.995% trace metals basis
Sigma-Aldrich
镍, wire, diam. 0.5 mm, ≥99.99% trace metals basis
Sigma-Aldrich
镍, wire, diam. 0.5 mm, ≥99.9% trace metals basis
镍, pellets, 100g, max. size 10mm, 99.999%
Sigma-Aldrich
镍, foil, thickness 0.1 mm, 99.98% trace metals basis
镍, foil, 100x100mm, thickness 0.25mm, annealed, 99%
Sigma-Aldrich
镍, sputtering target, diam. × thickness 2.00 in. × 0.25 in., 99.95% trace metals basis
镍, pellets, 20g, max. size 5mm, 99.99+%
镍, foil, 100x100mm, thickness 0.1mm, annealed, 99%
镍, foil, 100x100mm, thickness 1.0mm, annealed, 99.98%
镍, rod, 100mm, diameter 1.5mm, 99.99+%
镍, mesh, 130x130mm, nominal aperture 0.34mm, thickness 0.025mm, wire diameter 0.041mm, 70 wires/inch, open area 80%, electro-formed mesh, 99.9%
镍, foil, 100x100mm, thickness 1.6mm, 99%
镍, sphere, 100pcs, diameter 3.0mm, precision sphere grade 200, 99%
镍, foil, light tested, 25x25mm, thickness 0.0125mm, 99.99+%
镍, foil, 2m coil, thickness 0.025mm, coil width 600mm, as rolled, 99%
镍, pellets, 100g, max. size 10mm, 99.99+%
镍, foil, not light tested, 25x25mm, thickness 0.001mm, 99.95%
镍, foil, 50x50mm, thickness 1.6mm, 99%
镍, mesh, 30x30mm, nominal aperture 0.34mm, thickness 0.025mm, wire diameter 0.041mm, 70 wires/inch, open area 80%, electro-formed mesh, 99.9%
镍, rod, 50mm, diameter 5.0mm, 99.99+%
镍, mesh, 100x250mm, nominal aperture 0.73mm, wire diameter 0.25mm, 26x26 wires/inch, open area 55%, plain weave mesh, 99%
镍, foil, 150x150mm, thickness 1.6mm, 99%